Battery
Testing
At Power Proving Solutions we offer our clients a range
of battery monitoring and test equipment so you can analyse,
manage and test your battery equipment at any time.
Your battery can be a valuable part of your business and
unfortunately unforseen wear and tear can eventually mean
power failure and potential damage or even suspension of
your business. With a competent monitoring and test system
you can dramatically improve battery reliability and reduce
the risk of loss of business and therefore money. This system
can also save money on costly preventative maintenance and
replacement or repair.
We are authorised distributors for Polytronic Engineering
who manufacture, distribute and sell a range of Battery
Monitors for UPS, Telecom and Commercial Battery Systems.
Our monitoring systems can analyse the performance of your
battery system over time providing you with valuable information
about your battery health.
Power Proving Services can offer a variety of battery monitoring
solutions from basic counters through to complicated online
battery monitors. The level of technology and sophistication
of our equipment can vary depending on your requirements.
Our systems vary from a simple and basic monitor that records
your power flow to systems that can set off automatic alarms
and call your mobile phone or pager with a voice message.
Catagories:
Battery Monitors |
Load Banks and Testers |
Remote Monitors
|
BTM4000
| view
pdf
The BTM4000 System is designed for large stationary
applications. It requires a PC on site loaded with
the BTM software, Concentrators and RS232 Converters.
Concentrators will monitor 1 to 14V cells irrespective
of battery type or manufacturer and can independently
measure intercell resistance.
For large amounts of batteries
multiple Concentrators are connected with fiber optic
cable. This allows the system to monitor up to 16,000
cells from a single computer. The modular design results
in fast scanning of even the largest batteries.
^
back to index |
 |
|
|
|
|
|
|
 |
CommonSense
| view
pdf
CommonSense is quite simply, a
single conductor monitoring wire. One common sensing
wire is connected to all the batteries being monitored.
This innovation cuts hours of installation time and
improves access to the cell for maintenance purposes.
There are no bulky wire harnesses to hook up. It can
be used in conjunction with any of our BTM systems.
^ back to index |
|
|
|
|
|
|
Factstar
| view
pdf
The Factstar is a powerful battery
cycle counter. The device uses Polytronics revolutionary
float current monitoring technique to determine battery
status. The counter records discharge / charge frequency
and duration, and will alarm the user of open or shorted
strings, high float current, and pending thermal runaway
conditions. All of which are common causes of battery
failure.
^ back to index |
 |
|
|
|
|
|
|
 |
BTM2000P
| view
pdf
The BTM2000P portable battery tester is one of the
smallest most cost effective battery testers on the
market. The device records voltages, dynamic cell
resistance, strap resistance, calculated specific
gravity and a battery index for up to 500 cells or
ten sites. Individual cells can be tested in less
then 5 seconds.
The data can be downloaded to a computer an analyzed
using the BTM Portable software. The software is Excel
based and can be used to track the battery history.
The device comes with either Kelvin probes or clips
and additional sets can be purchased separately.
^ back to index |
|
|
|
|
|
|
BTM1200L
| view
pdf
The BTM1200L is one of the most
powerful portable load banks on the market. It even
meets standard airline baggage restrictions. The 1200L
can discharge 48V system at 400 Amps and 24V systems
at 200 Amps.
The load is transistor controlled
and the unit can be operated with or without computer
control. A built in BTM monitor logs battery data.
Additional monitors may be purchased and used in conjunction
with the load bank to acquire a more detailed picture
of the battery discharge.
^ back to index |
 |
|
|
|
|
|
|
 |
BTM1200LM
| view
pdf
The BTM1200LM is the possibly the smallest load bank
on the market. Despite it's small size the unit is
powerful enough to handle a 100 amp or 6kW discharge.
A built in BTM monitor logs battery data. Additional
monitors may be purchased and used in conjunction
with the load bank to acquire a more detailed picture
of the battery discharge. Multiple units may be used
in conjunction to discharge larger batteries.
^ back to index |
|
|
|
|
|
|
BTM
Global System | view
pdf
BTM-GLOBAL System is a battery monitoring system,
which aims to provide battery health related data
not only locally (in the battery or control room),
but also globally to specified locations. Like a central
monitoring station, using the Internet for connectivity.
The system is also capable of utilizing varous communication
links such as E-mail, Voice, Pager messages, for announcing
critical conditions in the battery room.
^ back to index |
 |
|
|
|
|
|
|
 |
BTM-Info
The BTM-Info is a device small enough to fit in your
hand, yet powerful enough to perform a full analysis
and store data for 10 full discharge/charge profiles
for up to five battery strings.
Loaded with 512 kB of memory (standard, expandable
up to 4 MB), this device can store a years worth of
information. It measures the batteries' vital parameters,
such as voltage, current, (optionally float-current)
and ambient/pilot temperature. The system also determines
the state and conition of the battery, charge rate
and predeicted capacity, among many others. This system
can can warn the user when there are outstanding conditions
detected for the battery, or individual jars. Warnings
can be enunciated locally and remopely (over PSTN
line) as alpha-numeric messages. Built-in backup-power
protects battery data against accidental AC-losses.
^ back to index |
|
|
|
|
|
|
|
